Rewind or replace, when an old motor stops being worth repairing

When a motor burns out, the decision that follows is usually made in a hurry and usually made on one number, the quoted repair cost against the quoted replacement cost. That comparison is incomplete often enough to be worth doing properly, because the repair almost always wins on price and quite often loses over the life of the machine.

What a rewind actually involves

The old winding is removed, which requires softening the varnish. Most workshops do this in a controlled burn off oven, where temperature is monitored to protect the stator core laminations. The slots are cleaned, new coils are wound and inserted, connections are made and the stator is impregnated with resin and cured.

Done well, by a workshop that controls its burn off temperature and uses insulation material of the correct class, a rewind restores the motor to close to its original condition. Done badly, with excessive burn off temperature, it damages the interlaminar insulation in the core and permanently increases iron losses.

That last point is where most of the efficiency loss associated with rewinding comes from. It is not inevitable and it is not universal. It is a function of the quality of the workshop.

The efficiency question, stated honestly

A well executed rewind on a motor with an undamaged core loses very little efficiency, often a few tenths of a percent or nothing measurable. A poor rewind can cost one or two percentage points, and repeated rewinds compound the damage.

The larger efficiency question is usually not the rewind at all. It is the age of the motor. A machine built before current efficiency rules may be a full class or two below what a new motor of the same rating achieves. Rewinding it preserves that gap for another decade.

The arithmetic is easy to do and rarely done. Take the rated output in kilowatts, divide by the old efficiency and by the new efficiency, take the difference, multiply by annual running hours and by the electricity price, and adjust for average load. For a motor running long hours, the annual difference between an old class and a current one is frequently larger than people expect. For a motor running a few hundred hours a year, it is negligible and the repair is obviously correct.

The factors that push towards replacement

Several conditions make replacement the better answer almost regardless of the quoted prices.

  • The motor has already been rewound twice or more. Each cycle risks further core damage and the machine is well past its original design life.
  • Running hours are high. Anything approaching continuous operation makes the efficiency difference dominate the comparison quickly.
  • The motor predates current efficiency requirements and no class is stated on the plate.
  • The core shows visible damage, burning between laminations or distortion. A core test should be part of any repair quotation and a failed core test ends the discussion.
  • The frame is a non standard or obsolete size that makes future repairs difficult, or the manufacturer no longer exists.
  • The failure was caused by the motor being wrong for the duty. Repairing it reproduces the same failure.

The factors that push towards repair

Equally, there are clear cases where repair is right.

  • Low running hours. A motor on a standby pump or an occasional hoist accumulates little energy cost, so efficiency barely matters.
  • Large frames and special machines. Above a few hundred kilowatts, and for slip ring, high voltage or specially flanged machines, replacement cost and lead time both rise steeply.
  • A motor that is already of a current efficiency class. Rewinding a recent IE3 or IE4 machine damaged by an external cause is straightforward economics.
  • Integrated or custom machines where the motor is part of a larger assembly and a standard replacement would not fit without redesign.
  • Immediate availability. If the plant is stopped and a repair can be done overnight while a replacement takes weeks, the cost of downtime settles the question on its own.

Lead time is part of the decision, not a footnote

The comparison changes entirely depending on whether a suitable replacement is available from stock or has to be manufactured. A standard frame low voltage motor in a common rating is usually a shelf item, and suppliers holding motors available for urgent delivery can often turn that part of the decision from weeks into days. A high voltage machine or an unusual mounting is a different situation and may take months.

This is the argument for deciding in advance rather than at the moment of failure. Knowing which motors in a plant are stock items and which are not, before anything breaks, converts an emergency into a routine replacement.

What to ask the repair workshop

A quotation that is only a price tells you nothing about which outcome you will get. Three questions separate a controlled process from a rough one.

First, what burn off temperature is used and how is it controlled. A properly managed oven with temperature monitoring is the single best indicator of a workshop that will not damage the core.

Second, is a core loss test performed before and after the burn off, and will the results be provided. This is the direct measurement of whether the core has been harmed.

Third, what insulation class will be fitted and will the original winding data be reproduced or changed. Rewinding to a higher insulation class is a genuine improvement. Quietly changing the number of turns to make the coils easier to wind is not, and it changes the motor characteristics.

A simple decision framework

If the motor runs more than about 4000 hours a year and has no stated efficiency class, replace it. If it runs less than about 1000 hours a year and the core tests sound, repair it. Between those two, calculate the energy difference over five years and compare it with the price difference rather than guessing.

Whichever route is chosen, the failure itself deserves an explanation. A motor that burned out because of unbalanced supply, a blocked cooling path or a duty it was never sized for will do it again, and neither a rewind nor a new machine will prevent that.

You Might Also Like