Anyone specifying, buying or repairing electric motors in Europe works under Commission Regulation 2019/1781, which replaced the earlier motor regulation and brought variable speed drives into scope for the first time. It is written as product law aimed at manufacturers, but its practical effects fall on the people choosing replacements.
What the regulation covers
It applies to electric motors placed on the European market, and to variable speed drives sold with or for them. It sets minimum efficiency classes, and it sets information requirements so that efficiency data has to be published and marked on the product.
The efficiency classes themselves are defined in the IEC 60034-30-1 standard, running from IE1 as the lowest through IE5 as the highest currently defined. Each step up represents roughly a 20 percent reduction in losses, not a 20 percent improvement in efficiency, which is why the percentage differences between classes look small on paper.
The first stage
From 1 July 2021, three phase motors rated from 0.75 to 1000 kilowatts with 2, 4, 6 or 8 poles had to reach at least IE3. Smaller three phase motors from 0.12 to 0.75 kilowatts had to reach at least IE2.
From the same date, variable speed drives in the 0.12 to 1000 kilowatt range had to meet at least efficiency class IE2 as defined for drives, which is a separate scale from the motor classes and refers to losses in the drive itself.
This stage removed IE1 motors from most of the market and ended the previous option of selling an IE2 motor provided it was supplied with a drive.
The second stage
From 1 July 2023, the requirement rose to IE4 for three phase motors rated from 75 to 200 kilowatts with 2, 4 or 6 poles. This is the band where the largest absolute energy savings are available, since motors of this size typically run long hours in continuous processes.
The same date extended coverage to several categories that had previously been exempt or subject to lower requirements, including single phase motors above 0.12 kilowatts, which must reach IE2, and motors with increased safety protection of type Ex eb, which came into scope at IE2.
Eight pole motors and a number of specialised categories remain at a lower requirement rather than being pulled up to IE4, because the economics and the available technology differ.
What is not covered
A number of exclusions remain, and they matter when specifying unusual machines. Motors fully integrated into a product where the efficiency cannot be tested independently, motors designed to operate wholly immersed in liquid, brake motors where the brake cannot be removed, and certain motors for ambient or altitude conditions outside the standard range are among them.
Motors intended purely as replacements for identical motors in existing products were the subject of a specific transitional arrangement, which is worth checking for older installations where a like for like replacement is genuinely the only option.
What it means for repair
This is the point that causes the most confusion. The regulation governs placing products on the market. It does not prohibit repairing an existing motor, and a rewound motor is not a new product placed on the market.
So rewinding an old IE1 motor remains entirely legal. What has changed is the economics, because the alternative is no longer another IE1 motor but a current one at IE3 or IE4. The efficiency gap between what you have and what you could buy is now wide enough that the comparison frequently favours replacement on running cost alone, particularly for motors operating long hours.
Reading the practical consequences
For anyone maintaining an installed base, three consequences follow.
First, spare motors held in stock for many years may no longer be representative of what can be bought. Stock rotation is worth reviewing, because a store full of obsolete class spares is a store of assets that cannot be replaced like for like when they run out.
Second, replacing an old motor with a current one usually means a different efficiency class, and higher efficiency motors have slightly different characteristics. They typically run at marginally higher speed because slip is lower, which on a centrifugal pump or fan increases absorbed power. On a belt drive the pulley ratio may need adjusting to avoid quietly increasing energy consumption while installing a more efficient motor.
Third, the starting current of high efficiency motors is generally higher than that of the machines they replace, because the same design changes that reduce losses reduce impedance. Protection settings and, on marginal supplies, starting arrangements are worth rechecking rather than assumed.
What comes next
The current text does not schedule a further tier beyond the 2023 stage. It does provide for review, and the direction of travel across the standards is clear, with IE5 now defined and increasingly available in synchronous reluctance and permanent magnet machines.
For planning purposes the sensible assumption is that requirements will tighten again rather than relax, and that the technologies which reach IE5 today will become normal rather than specialist. Specifying above the current minimum on any motor expected to remain in service for fifteen or twenty years is a reasonable hedge, and on long running drives it usually pays for itself regardless of future regulation.
A note on comparing efficiency figures
Efficiency classes are defined at rated load. Real motors rarely run at exactly rated load, and the shape of the efficiency curve between classes differs. Higher class motors generally hold their efficiency better at partial load, which means the real saving on a lightly loaded drive can be larger than the nameplate comparison suggests.
Conversely, comparing a 2 pole and a 4 pole motor of the same class is not comparing like with like, since the class thresholds differ by pole count and by power. The only meaningful comparison is between the actual efficiency percentages published for the specific machines, at the actual load the application imposes. Supplier ranges of electric motors built to the current efficiency classes publish those figures per rating, which makes a genuine comparison possible rather than a class label comparison.



